B2B Telecom Equipment Supplier — Request a Quote Todayتأمین‌کننده B2B تجهیزات مخابراتی — امروز درخواست قیمت کنید
B2B Telecom Equipment Supplier — Request a Quote Todayتأمین‌کننده B2B تجهیزات مخابراتی — امروز درخواست قیمت کنید
2G/3G/4G/5G Network Equipment — Nokia, Ericsson, Huawei, ZTE & Moreتجهیزات شبکه 2G/3G/4G/5G — Nokia، Ericsson، Huawei، ZTE و بیشتر
2G/3G/4G/5G Network Equipment — Nokia, Ericsson, Huawei, ZTE & Moreتجهیزات شبکه 2G/3G/4G/5G — Nokia، Ericsson، Huawei، ZTE و بیشتر
Worldwide Shipping
Sea freight, land transport, air freight

PON Split Ratios Explained: 1:32 vs 1:64 vs 1:128 and OLT Port Budgeting PON Split Ratios Explained: 1:32 vs 1:64 vs 1:128 and OLT Port Budgeting

Nov 15, 2026

One GPON port on an OLT can carry 2.488 Gbps downstream. How many homes that single port serves is a business decision expressed as a split ratio: 1:32, 1:64 or 1:128. The optical physics sets hard boundaries, and staying inside them is mostly arithmetic on an loss budget.

What the Standards Allow

ITU-T G.984 defines GPON with logical reach of 60 km and differential reach of 20 km. In practice, Class B+ optics support up to 1:64 in favorable plants, while Class C+ (and C++) optics with their higher transmit power and sensitivity are what make 1:128 dependable. If your deployment plan says 1:128, it also says C+ optics — the two decisions are not separable.

The Loss Budget Walkthrough

Work it out end to end for a 1:64 build with Class B+:
- Splitter insertion loss: about 20.5 dB for 1:64 (about 17.5 dB for 1:32, 24 dB for 1:128)
- Fiber attenuation: 0.35 dB/km at 1490 nm downstream — 10 km of plant is 3.5 dB
- Connectors and splices: budget 0.3 dB per connector pair and 0.1 dB per splice; a typical path with 2 connectors and 6 splices adds roughly 1.2 dB
- Total for the example: about 25.2 dB

Class B+ gives you a 13–28 dB budget; 25.2 dB fits, but with under 3 dB of margin. The same plant at 1:128 needs about 28.7 dB — already past B+ territory, which is exactly why 1:128 is specified with C+ (17–30 dB). When you plan, leave at least 2–3 dB of margin for aging connectors, emergency restore splices, and the ONT that inevitably sits 2 km farther than the survey said.

Bandwidth Is the Other Ceiling

Optics decide whether a split is possible; bandwidth decides whether it is sensible. At 1:64, 2.488 Gbps shared means an average of about 39 Mbps of downstream capacity per subscriber before oversubscription gains — workable for FTTH residential with today's traffic profiles, thin for business lines. At 1:128 it averages under 20 Mbps, which is why high-ratio builds target low-usage demographics or lean on XGS-PON's 10 Gbps downstream. GPON and XGS-PON coexist on the same ODN through a combiner, so a ratio that is tight today can be relieved later without re-cabling.

Practical Planning Rules

- Match the split to the demographics: 1:32 for business parks and premium tiers, 1:64 as the general-purpose default, 1:128 for low-ARPU greenfield.
- Put the splitter as close to subscribers as plant topology allows; every meter before the splitter is paid at full fiber loss for all subscribers behind it.
- Buy OLT boards and ONTs as matched optics classes — a C+ board with B+ ONTs inherits B+ behavior.
- Document per-PON-path measured loss at turn-up; it is your baseline for troubleshooting years later.

Equipment Note

Boxin Telecom stocks GPON OLT boards (Class B+ and C+), ONU/ONT units and splitters across Huawei, ZTE and FiberHome lines, with Yantai and Hong Kong warehousing. Send your plant profile — reach, split target, subscriber count — to Rock: WhatsApp/Telegram/WeChat +86 186 6005 1788, email [email protected], and we will confirm optics class and board options with a quotation within 24 hours.

One GPON port on an OLT can carry 2.488 Gbps downstream. How many homes that single port serves is a business decision expressed as a split ratio: 1:32, 1:64 or 1:128. The optical physics sets hard boundaries, and staying inside them is mostly arithmetic on an loss budget.

What the Standards Allow

ITU-T G.984 defines GPON with logical reach of 60 km and differential reach of 20 km. In practice, Class B+ optics support up to 1:64 in favorable plants, while Class C+ (and C++) optics with their higher transmit power and sensitivity are what make 1:128 dependable. If your deployment plan says 1:128, it also says C+ optics — the two decisions are not separable.

The Loss Budget Walkthrough

Work it out end to end for a 1:64 build with Class B+:
- Splitter insertion loss: about 20.5 dB for 1:64 (about 17.5 dB for 1:32, 24 dB for 1:128)
- Fiber attenuation: 0.35 dB/km at 1490 nm downstream — 10 km of plant is 3.5 dB
- Connectors and splices: budget 0.3 dB per connector pair and 0.1 dB per splice; a typical path with 2 connectors and 6 splices adds roughly 1.2 dB
- Total for the example: about 25.2 dB

Class B+ gives you a 13–28 dB budget; 25.2 dB fits, but with under 3 dB of margin. The same plant at 1:128 needs about 28.7 dB — already past B+ territory, which is exactly why 1:128 is specified with C+ (17–30 dB). When you plan, leave at least 2–3 dB of margin for aging connectors, emergency restore splices, and the ONT that inevitably sits 2 km farther than the survey said.

Bandwidth Is the Other Ceiling

Optics decide whether a split is possible; bandwidth decides whether it is sensible. At 1:64, 2.488 Gbps shared means an average of about 39 Mbps of downstream capacity per subscriber before oversubscription gains — workable for FTTH residential with today's traffic profiles, thin for business lines. At 1:128 it averages under 20 Mbps, which is why high-ratio builds target low-usage demographics or lean on XGS-PON's 10 Gbps downstream. GPON and XGS-PON coexist on the same ODN through a combiner, so a ratio that is tight today can be relieved later without re-cabling.

Practical Planning Rules

- Match the split to the demographics: 1:32 for business parks and premium tiers, 1:64 as the general-purpose default, 1:128 for low-ARPU greenfield.
- Put the splitter as close to subscribers as plant topology allows; every meter before the splitter is paid at full fiber loss for all subscribers behind it.
- Buy OLT boards and ONTs as matched optics classes — a C+ board with B+ ONTs inherits B+ behavior.
- Document per-PON-path measured loss at turn-up; it is your baseline for troubleshooting years later.

Equipment Note

Boxin Telecom stocks GPON OLT boards (Class B+ and C+), ONU/ONT units and splitters across Huawei, ZTE and FiberHome lines, with Yantai and Hong Kong warehousing. Send your plant profile — reach, split target, subscriber count — to Rock: WhatsApp/Telegram/WeChat +86 186 6005 1788, email [email protected], and we will confirm optics class and board options with a quotation within 24 hours.

Back to newsبازگشت به اخبار

Post commentارسال دیدگاه

Comments are reviewed before publication.دیدگاه‌ها پس از بررسی منتشر می‌شوند.