GPON ONT Compared: HG8546M vs F660 vs EG8141A5
Short answer: only one of the three has a published port mix. The EG8141A5 (ET8141A5CUS) page states 1GE + 3FE + 1TEL + 1USB + WiFi on 2.4 GHz, one 10/100/1000 adaptive RJ45 LAN port, a single-fiber GPON/EPON/XPON interface at 2.5 Gbps down / 1.25 Gbps up, Tx 1310 nm / Rx 1490 nm, and 12 V 1.0 A DC input [S1]. The HG8546M page states only the model, the white colour and a 5 dBi external antenna [S4]. The ZTE F660 appears twice on the site with different data: F660 V6 is listed with a SC/UPC PON port, external antenna, 0.3 kg weight and 1-year warranty [S2], while F660 V5.2 is listed with 1 port, single-fiber single-mode fiber, ABS housing and 1310/1550 nm wavelength [S3]. If you are writing a purchase order today, the EG8141A5 is the only model whose port list you can copy from the page.
This article uses only what the four product pages publish. Where a page is silent, the article says "not stated on page" instead of borrowing a number from a datasheet you have not seen.
1. What each page actually publishes
1.1 HG8546M — a title, a colour, an antenna
The HG8546M page lists: product name "EchoLife HG8546M XPON ONU", model HG8546M, colour white, antenna 5 dBi external antenna [S4]. That is the entire specification table. There is no port count, no WiFi band, no PON interface type, no power figure and no temperature range on that page.
A separate listing bundles the HG8546M with the EG8141A5 in the product title: "EG8141A5 HG8546M Router, EG8141A5 ONU All Brand XPON GPON EPON" [S1]. The technical table on that page describes the ET8141A5CUS model specifically, so it should not be read as HG8546M data.
Practical consequence: for HG8546M, you must request the port configuration and the PON module type from the seller before quoting an FTTH rollout. The page cannot settle it.
1.2 ZTE F660 V6 — a PON port, an antenna, a weight
The F660 V6 page publishes: model F660 V6, type ONU, use FTTX, network wired LAN, weight 0.3 kg, PON port SC/UPC, external antenna, 1-year warranty, 1 pc per inner box, OEM accepted [S2].
It does not state the number of LAN ports, the WiFi band, the PON rate, the wavelength, the power input or the operating temperature.
1.3 ZTE F660 V5.2 — a different data set
The F660 V5.2 page publishes: 1 port, single-fiber single-mode fiber, ABS housing, white, wavelength 1310/1550 nm, low power dissipation, application FTTH/FTTX, 1-year or 12-month warranty [S3].
Note the wavelength line. The V5.2 page lists 1310/1550 nm; the EG8141A5 page lists Tx 1310 nm / Rx 1490 nm [S1][S3]. Both are printed on the pages as listed. This article does not reconcile them — ask the seller which downstream wavelength applies to the exact unit being shipped, because it changes what the drop-side optics must support.
1.4 EG8141A5 — the full table
The EG8141A5 page is the only one of the four with a complete specification block [S1]:
| Item | Value as listed |
|---|---|
| Model | ET8141A5CUS |
| Out ports | 1GE + 3FE + 1TEL + 1USB + WiFi |
| WiFi | 2.4G |
| Wireless gain | 5 db |
| USB | USB 2.0 |
| LAN | 1 x 10/100/1000 Mbps adaptive Ethernet, full/half duplex, RJ45 |
| TEL | H248 / SIP voice protocol |
| PPPoE | Supported |
| Firmware | English |
| Dimension / weight | 155 x 125 x 30 mm / 222 g |
| Fiber port | 1 GPON/EPON/XPON interface, single-fiber, downstream 2.5 Gbps, upstream 1.25 Gbps |
| Wavelength | Tx 1310 nm, Rx 1490 nm |
| Fiber interface | SC/FC-UPC/APC, dual mode / single mode |
| RX sensitivity | > -28 dBm at 1490 nm |
| DC power | 12 V 1.0 A, external AC-DC adapter |
| Buttons | Reset, power, WPS, WLAN |
| Working environment | -5 to +55 °C, 10–90% RH non-condensing |
| Storage environment | -30 to +60 °C, 10–90% RH non-condensing |
The page also lists five platform features: plug-and-play provisioning from the NMS with no on-site configuration, remote fault locating via POTS loop-line test and PPPoE dial-up emulation, end-to-end link monitoring through 802.1ag Ethernet OAM, 900 Mbit/s forwarding in the NAT scenario, and IPv6/IPv4 dual stack with DS-Lite [S1].
2. Side-by-side
| Item | HG8546M | ZTE F660 V6 | ZTE F660 V5.2 | EG8141A5 (ET8141A5CUS) |
|---|---|---|---|---|
| PON type | not stated | not stated (type ONU) | not stated (GPON per title) | GPON / EPON / XPON |
| PON port | not stated | SC/UPC | not stated | SC/FC-UPC/APC, dual or single mode |
| Port mix | not stated | not stated | 1 port | 1GE + 3FE + 1TEL + 1USB |
| LAN rate | not stated | not stated | not stated | 10/100/1000 adaptive |
| WiFi | not stated | external antenna | not stated | 2.4G, 5 db gain |
| Wavelength | not stated | not stated | 1310 / 1550 nm | Tx 1310 / Rx 1490 nm |
| Voice | not stated | not stated | not stated | H248 / SIP |
| Power | not stated | not stated | not stated | 12 V 1.0 A external adapter |
| Operating temp | not stated | not stated | not stated | -5 to +55 °C |
| Weight | not stated | 0.3 kg | not stated | 222 g |
| Housing | white | not stated | ABS, white | not stated |
| Warranty | not stated | 1 year | 1 year / 12 months | not stated |
| Source | S4 | S2 | S3 | S1 |
That table is deliberately full of "not stated". It is the honest picture of the four pages, and it is also the reason an ONT RFQ needs more fields than a model name.
3. How to choose between them
3.1 Start from the service mix, not the brand
- Broadband only, one LAN device: a single-port ONT is sufficient — F660 V5.2 is listed as 1 port [S3].
- Broadband plus a landline: you need a TEL port with H248 or SIP — the EG8141A5 page explicitly lists both protocols [S1].
- Broadband plus IPTV plus a second LAN drop: the 1GE + 3FE layout on EG8141A5 covers four copper drops plus WiFi [S1].
- WiFi coverage in a large flat: antenna gain matters more than the model name. HG8546M is listed with a 5 dBi external antenna [S4]; EG8141A5 is listed with 5 db wireless gain and 2.4 GHz only [S1]. Neither page states 5 GHz support.
3.2 Then check what the OLT expects
The ONT must match the OLT's PON type. The EG8141A5 is listed as GPON/EPON/XPON capable on one single-fiber interface with 2.5 Gbps downstream and 1.25 Gbps upstream [S1]. The F660 V6 page gives the PON connector (SC/UPC) but not the PON rate [S2]. The F660 V5.2 page gives the wavelength but not the connector [S3].
If the OLT side is a ZTE MA5680T / MA5683T / MA5608T or an MA5800 with C+ / C++ modules, the OLT board's per-port ONU ceiling and split ratio set how many ONTs a tree can hold — see the GPON OLT board class note for those numbers.
3.3 Watch the connector
SC/UPC and SC/APC are not interchangeable at the same loss budget, and the EG8141A5 page lists SC/FC-UPC/APC across dual-mode and single-mode fiber [S1], while the F660 V6 page lists SC/UPC [S2] and the F660 V5.2 listing on the site references SC/APC in its title. Confirm the connector on the exact SKU before terminating drop cables — a mismatched APC/UPC pair is a field rework item, not a documentation issue.
3.4 Do not assume the missing rows
The three models without a published port table are not worse products; they are under-documented listings. In a tender, an undocumented ONT is a risk item: you cannot prove port count, WiFi band or power input from the page. Ask for a photo of the rear panel and a label shot for every model you intend to buy in volume.
4. Recommendation
- Fastest path to a defensible RFQ: EG8141A5 (ET8141A5CUS) — it is the only model here whose port mix, PON rate, wavelength, connector, power and temperature are all published [S1].
- Voice service required: EG8141A5, because H248/SIP is explicitly stated [S1].
- Single-port, cost-driven FTTH drop: F660 V5.2 as listed with 1 port and 1310/1550 nm [S3] — confirm the PON rate and connector first.
- SC/UPC plant already terminated: F660 V6 lists SC/UPC [S2] — confirm port count before ordering.
- Large indoor WiFi coverage: HG8546M with its 5 dBi external antenna [S4] — but request the full port and PON spec, since the page does not publish them.
- Any bulk order: require a rear-panel photo and a label photo per model. Three of these four pages cannot answer basic port questions.
5. Where to buy
- EG8141A5 ONU, all-brand XPON/GPON/EPON, 1GE+3FE+1TEL+1USB: https://boxintelecom.com/products/eg8141a5-hg8546m-router-eg8141a5-onu-all-brand-xpon-gpon-epon-hg8546m-eg8141a5
- ZTE F660 V6 GPON ONT with WiFi router: https://boxintelecom.com/products/high-quality-fiber-optical-equipment-gpon-ont-f660-6.0-v6.0-wifi-router
- ZTE ZXHN F660 V5.2 GPON international version: https://boxintelecom.com/products/zte-ont-onu-zxhn-f660-v5.2-gpon-international-version-sc-apc-zte-f660
- HG8546M XPON ONU: https://boxintelecom.com/products/new-brand-hg8546m-xpon-enterprise-wireless-access-points-featuring-gpon-technology
- HG8010H / EG8010H / HG8546M English-version XPON ONT: https://boxintelecom.com/products/ftth-ont-as-hg8010h-eg8010h-xpon-hg8546m-english-version-router-fiber-onu-xpon-gepon-onu
- ONT and WiFi router collection: https://boxintelecom.com/collections/olt-onu-ont-wifi-router
Send the OLT model, the required port mix and the connector type in one message; the quote comes back within 24 hours.
Sources
- [S1] EG8141A5 (ET8141A5CUS) specification table and feature list — https://boxintelecom.com/products/eg8141a5-hg8546m-router-eg8141a5-onu-all-brand-xpon-gpon-epon-hg8546m-eg8141a5
- [S2] ZTE F660 V6 specification table — https://boxintelecom.com/products/high-quality-fiber-optical-equipment-gpon-ont-f660-6.0-v6.0-wifi-router
- [S3] ZTE ZXHN F660 V5.2 listing — https://boxintelecom.com/products/zte-ont-onu-zxhn-f660-v5.2-gpon-international-version-sc-apc-zte-f660
- [S4] HG8546M XPON ONU listing — https://boxintelecom.com/products/new-brand-hg8546m-xpon-enterprise-wireless-access-points-featuring-gpon-technology
Product pages do not publish prices; this store quotes by request.
Publisher notes (not for publication)
Internal links to add in the body: - → https://boxintelecom.com/collections/olt-onu-ont-wifi-router (anchor: "ONT and WiFi router range") - → /posts/01-zte-olt-chassis-ma5680t-ma5683t-ma5608t(发布后按最终路径替换) (anchor: "ZTE OLT chassis options") - → https://boxintelecom.com/collections/optical-cable-optical-fiber-odn-optical-communication-passive-devices-pigtail-fiber-jumper (anchor: "drop cable and pigtails")
Keyword density check: hg8546m 23x, f660 28x in 1,445 words ≈ 1.6% / 1.9%. Model codes only; the comparison table carries most of them.
Suggested images: 1. Rear-panel photo of the EG8141A5 showing the 1GE + 3FE + 1TEL + 1USB layout — caption "the only model here with a published port mix". 2. Label close-up of a ZTE F660 showing the SC/UPC port — caption "F660 V6: SC/UPC PON port". 3. Side-by-side size shot: 155 x 125 x 30 mm EG8141A5 against the 0.3 kg F660 V6 — caption with the published dimensions.
GPON ONT Compared: HG8546M vs F660 vs EG8141A5
Short answer: only one of the three has a published port mix. The EG8141A5 (ET8141A5CUS) page states 1GE + 3FE + 1TEL + 1USB + WiFi on 2.4 GHz, one 10/100/1000 adaptive RJ45 LAN port, a single-fiber GPON/EPON/XPON interface at 2.5 Gbps down / 1.25 Gbps up, Tx 1310 nm / Rx 1490 nm, and 12 V 1.0 A DC input [S1]. The HG8546M page states only the model, the white colour and a 5 dBi external antenna [S4]. The ZTE F660 appears twice on the site with different data: F660 V6 is listed with a SC/UPC PON port, external antenna, 0.3 kg weight and 1-year warranty [S2], while F660 V5.2 is listed with 1 port, single-fiber single-mode fiber, ABS housing and 1310/1550 nm wavelength [S3]. If you are writing a purchase order today, the EG8141A5 is the only model whose port list you can copy from the page.
This article uses only what the four product pages publish. Where a page is silent, the article says "not stated on page" instead of borrowing a number from a datasheet you have not seen.
1. What each page actually publishes
1.1 HG8546M — a title, a colour, an antenna
The HG8546M page lists: product name "EchoLife HG8546M XPON ONU", model HG8546M, colour white, antenna 5 dBi external antenna [S4]. That is the entire specification table. There is no port count, no WiFi band, no PON interface type, no power figure and no temperature range on that page.
A separate listing bundles the HG8546M with the EG8141A5 in the product title: "EG8141A5 HG8546M Router, EG8141A5 ONU All Brand XPON GPON EPON" [S1]. The technical table on that page describes the ET8141A5CUS model specifically, so it should not be read as HG8546M data.
Practical consequence: for HG8546M, you must request the port configuration and the PON module type from the seller before quoting an FTTH rollout. The page cannot settle it.
1.2 ZTE F660 V6 — a PON port, an antenna, a weight
The F660 V6 page publishes: model F660 V6, type ONU, use FTTX, network wired LAN, weight 0.3 kg, PON port SC/UPC, external antenna, 1-year warranty, 1 pc per inner box, OEM accepted [S2].
It does not state the number of LAN ports, the WiFi band, the PON rate, the wavelength, the power input or the operating temperature.
1.3 ZTE F660 V5.2 — a different data set
The F660 V5.2 page publishes: 1 port, single-fiber single-mode fiber, ABS housing, white, wavelength 1310/1550 nm, low power dissipation, application FTTH/FTTX, 1-year or 12-month warranty [S3].
Note the wavelength line. The V5.2 page lists 1310/1550 nm; the EG8141A5 page lists Tx 1310 nm / Rx 1490 nm [S1][S3]. Both are printed on the pages as listed. This article does not reconcile them — ask the seller which downstream wavelength applies to the exact unit being shipped, because it changes what the drop-side optics must support.
1.4 EG8141A5 — the full table
The EG8141A5 page is the only one of the four with a complete specification block [S1]:
| Item | Value as listed |
|---|---|
| Model | ET8141A5CUS |
| Out ports | 1GE + 3FE + 1TEL + 1USB + WiFi |
| WiFi | 2.4G |
| Wireless gain | 5 db |
| USB | USB 2.0 |
| LAN | 1 x 10/100/1000 Mbps adaptive Ethernet, full/half duplex, RJ45 |
| TEL | H248 / SIP voice protocol |
| PPPoE | Supported |
| Firmware | English |
| Dimension / weight | 155 x 125 x 30 mm / 222 g |
| Fiber port | 1 GPON/EPON/XPON interface, single-fiber, downstream 2.5 Gbps, upstream 1.25 Gbps |
| Wavelength | Tx 1310 nm, Rx 1490 nm |
| Fiber interface | SC/FC-UPC/APC, dual mode / single mode |
| RX sensitivity | > -28 dBm at 1490 nm |
| DC power | 12 V 1.0 A, external AC-DC adapter |
| Buttons | Reset, power, WPS, WLAN |
| Working environment | -5 to +55 °C, 10–90% RH non-condensing |
| Storage environment | -30 to +60 °C, 10–90% RH non-condensing |
The page also lists five platform features: plug-and-play provisioning from the NMS with no on-site configuration, remote fault locating via POTS loop-line test and PPPoE dial-up emulation, end-to-end link monitoring through 802.1ag Ethernet OAM, 900 Mbit/s forwarding in the NAT scenario, and IPv6/IPv4 dual stack with DS-Lite [S1].
2. Side-by-side
| Item | HG8546M | ZTE F660 V6 | ZTE F660 V5.2 | EG8141A5 (ET8141A5CUS) |
|---|---|---|---|---|
| PON type | not stated | not stated (type ONU) | not stated (GPON per title) | GPON / EPON / XPON |
| PON port | not stated | SC/UPC | not stated | SC/FC-UPC/APC, dual or single mode |
| Port mix | not stated | not stated | 1 port | 1GE + 3FE + 1TEL + 1USB |
| LAN rate | not stated | not stated | not stated | 10/100/1000 adaptive |
| WiFi | not stated | external antenna | not stated | 2.4G, 5 db gain |
| Wavelength | not stated | not stated | 1310 / 1550 nm | Tx 1310 / Rx 1490 nm |
| Voice | not stated | not stated | not stated | H248 / SIP |
| Power | not stated | not stated | not stated | 12 V 1.0 A external adapter |
| Operating temp | not stated | not stated | not stated | -5 to +55 °C |
| Weight | not stated | 0.3 kg | not stated | 222 g |
| Housing | white | not stated | ABS, white | not stated |
| Warranty | not stated | 1 year | 1 year / 12 months | not stated |
| Source | S4 | S2 | S3 | S1 |
That table is deliberately full of "not stated". It is the honest picture of the four pages, and it is also the reason an ONT RFQ needs more fields than a model name.
3. How to choose between them
3.1 Start from the service mix, not the brand
- Broadband only, one LAN device: a single-port ONT is sufficient — F660 V5.2 is listed as 1 port [S3].
- Broadband plus a landline: you need a TEL port with H248 or SIP — the EG8141A5 page explicitly lists both protocols [S1].
- Broadband plus IPTV plus a second LAN drop: the 1GE + 3FE layout on EG8141A5 covers four copper drops plus WiFi [S1].
- WiFi coverage in a large flat: antenna gain matters more than the model name. HG8546M is listed with a 5 dBi external antenna [S4]; EG8141A5 is listed with 5 db wireless gain and 2.4 GHz only [S1]. Neither page states 5 GHz support.
3.2 Then check what the OLT expects
The ONT must match the OLT's PON type. The EG8141A5 is listed as GPON/EPON/XPON capable on one single-fiber interface with 2.5 Gbps downstream and 1.25 Gbps upstream [S1]. The F660 V6 page gives the PON connector (SC/UPC) but not the PON rate [S2]. The F660 V5.2 page gives the wavelength but not the connector [S3].
If the OLT side is a ZTE MA5680T / MA5683T / MA5608T or an MA5800 with C+ / C++ modules, the OLT board's per-port ONU ceiling and split ratio set how many ONTs a tree can hold — see the GPON OLT board class note for those numbers.
3.3 Watch the connector
SC/UPC and SC/APC are not interchangeable at the same loss budget, and the EG8141A5 page lists SC/FC-UPC/APC across dual-mode and single-mode fiber [S1], while the F660 V6 page lists SC/UPC [S2] and the F660 V5.2 listing on the site references SC/APC in its title. Confirm the connector on the exact SKU before terminating drop cables — a mismatched APC/UPC pair is a field rework item, not a documentation issue.
3.4 Do not assume the missing rows
The three models without a published port table are not worse products; they are under-documented listings. In a tender, an undocumented ONT is a risk item: you cannot prove port count, WiFi band or power input from the page. Ask for a photo of the rear panel and a label shot for every model you intend to buy in volume.
4. Recommendation
- Fastest path to a defensible RFQ: EG8141A5 (ET8141A5CUS) — it is the only model here whose port mix, PON rate, wavelength, connector, power and temperature are all published [S1].
- Voice service required: EG8141A5, because H248/SIP is explicitly stated [S1].
- Single-port, cost-driven FTTH drop: F660 V5.2 as listed with 1 port and 1310/1550 nm [S3] — confirm the PON rate and connector first.
- SC/UPC plant already terminated: F660 V6 lists SC/UPC [S2] — confirm port count before ordering.
- Large indoor WiFi coverage: HG8546M with its 5 dBi external antenna [S4] — but request the full port and PON spec, since the page does not publish them.
- Any bulk order: require a rear-panel photo and a label photo per model. Three of these four pages cannot answer basic port questions.
5. Where to buy
- EG8141A5 ONU, all-brand XPON/GPON/EPON, 1GE+3FE+1TEL+1USB: https://boxintelecom.com/products/eg8141a5-hg8546m-router-eg8141a5-onu-all-brand-xpon-gpon-epon-hg8546m-eg8141a5
- ZTE F660 V6 GPON ONT with WiFi router: https://boxintelecom.com/products/high-quality-fiber-optical-equipment-gpon-ont-f660-6.0-v6.0-wifi-router
- ZTE ZXHN F660 V5.2 GPON international version: https://boxintelecom.com/products/zte-ont-onu-zxhn-f660-v5.2-gpon-international-version-sc-apc-zte-f660
- HG8546M XPON ONU: https://boxintelecom.com/products/new-brand-hg8546m-xpon-enterprise-wireless-access-points-featuring-gpon-technology
- HG8010H / EG8010H / HG8546M English-version XPON ONT: https://boxintelecom.com/products/ftth-ont-as-hg8010h-eg8010h-xpon-hg8546m-english-version-router-fiber-onu-xpon-gepon-onu
- ONT and WiFi router collection: https://boxintelecom.com/collections/olt-onu-ont-wifi-router
Send the OLT model, the required port mix and the connector type in one message; the quote comes back within 24 hours.
Sources
- [S1] EG8141A5 (ET8141A5CUS) specification table and feature list — https://boxintelecom.com/products/eg8141a5-hg8546m-router-eg8141a5-onu-all-brand-xpon-gpon-epon-hg8546m-eg8141a5
- [S2] ZTE F660 V6 specification table — https://boxintelecom.com/products/high-quality-fiber-optical-equipment-gpon-ont-f660-6.0-v6.0-wifi-router
- [S3] ZTE ZXHN F660 V5.2 listing — https://boxintelecom.com/products/zte-ont-onu-zxhn-f660-v5.2-gpon-international-version-sc-apc-zte-f660
- [S4] HG8546M XPON ONU listing — https://boxintelecom.com/products/new-brand-hg8546m-xpon-enterprise-wireless-access-points-featuring-gpon-technology
Product pages do not publish prices; this store quotes by request.
Publisher notes (not for publication)
Internal links to add in the body: - → https://boxintelecom.com/collections/olt-onu-ont-wifi-router (anchor: "ONT and WiFi router range") - → /posts/01-zte-olt-chassis-ma5680t-ma5683t-ma5608t(发布后按最终路径替换) (anchor: "ZTE OLT chassis options") - → https://boxintelecom.com/collections/optical-cable-optical-fiber-odn-optical-communication-passive-devices-pigtail-fiber-jumper (anchor: "drop cable and pigtails")
Keyword density check: hg8546m 23x, f660 28x in 1,445 words ≈ 1.6% / 1.9%. Model codes only; the comparison table carries most of them.
Suggested images: 1. Rear-panel photo of the EG8141A5 showing the 1GE + 3FE + 1TEL + 1USB layout — caption "the only model here with a published port mix". 2. Label close-up of a ZTE F660 showing the SC/UPC port — caption "F660 V6: SC/UPC PON port". 3. Side-by-side size shot: 155 x 125 x 30 mm EG8141A5 against the 0.3 kg F660 V6 — caption with the published dimensions.